NEW BUILD – Blyth 14m Series ( ID:588088 )





TEL: +44 7798 607 323 


MAKE:   Blyth 14m Workcat


YEAR:   New Build


BUILDER:   Blyth Catamarans


LOA:   14.00m
BEAM:   4.96m
DRAFT:   0.80m
LOCATION:   Ex. Factory UK




Click to Email:            




Blyth Workcats established and well-proven design 14 metre Catamaran. We know that the way workboats are used varies greatly and we appreciate that in order to get the very best out of a workboat, it must be customised to match exactly the specific needs for a particular operation. The existing range of 10m, 11m, 12m and 14m Blyth Workcats has given excellent service in a wide variety of uses and environments. 

Hull with stringers

Wheel house std size assembled

Additions to std wheel house to 18ft with roof extension

Iveco C9 620 (550)

MCA COP 12+2 /60 miles Cat 2 SVC



Note: New W/House, fwd facing windows, observation plinth

All ply bulkheads, deck supports (transverse and longitudinal),

deck support timbers bonded into hull and crash tanks

Plydecks fitted and sheaved

Non-slip finish applied to deck and coated in polyester

Flo coat to all GRP surfaces of mouldings

Engine GRP vents alongside toilet bulkhead

Engine Bearers

Small deck hatches and surrounds, drains and catches

Engine hatches and surrounds per pair

Aft deck combing

Fwd deck combing (not required with full deck) 1m of deckLarge Radar arch in stainless steel

Cut out scupper and gel exposed glass fibre edges


Hull and deck fittings / work

Supply and fit stainless steel boarding ladder

Wheelhouse access ladder

Lining to wheel house - sides only in cord

Lining to wheel house roof in foam-backed vinyl

Toilet unit fabrication on deck unit, including door

Separate Shower

Door in Port and Stbd gunwale

Fwd structure floor in each fwd hull


Windows supplied and fitted with one access door (800mm)

Additional door supplied and fitted

Observation plinth windows

Rails supplied ex foredeck rails (for Island wheel house)

Spring cleats

Supply and fit 4 heavy duty bollards

Nav lights supplied and fitted with cables run to helm and

connected to panel (excludes panel)

Enclose bilges under engines

Gel below gunwales from deck to combing

Deck Cargo Tie Down Points x 8 aft 4 fwd

Watertight Deck Access Hatches x 4

Remote Fuel Shut Off Control

Helm fabricated option

Supply and fit Bench Seating

Cushions for Bench Seating

Supply simple galley unit laminate, teak capped

Microwave, Halogen 2 Burner Cooker & Fridge Fitted

Fire retardant gelcoat to engine bays (grey)

Helm Seat supplied + fit on GRP box

12 Cleeman Seats on GRP Storage Boxes

Wheelhouse Floor in Vinyl Disc Tiles

Supply and fit 5" D fendering

Additional fendering on stern quarters and around transom


Click to See Video of 14m Blyth Workcat Sea Trials



Fit engines supplied by Blyth workcats

Install stern gear supplied 2" shafts

Sure Seals

Supply and fit anodes wired to shafts

Supply and fit engine sound insulation to engine hatch lids

Supply and fit twin propellers over 370 hp


Fuel System

2 x pre-filters with fuel lines and fuel cut off valves

Supply and fit 2 x 300gal (approx) fuel tanks

Tank gauges and senders



Standard 24v wiring, N:B this price should

be used as a guide only as changes according

to specification will effect final costing ( price assumes 3 x 8 way switch panels)

3kw Inverter/charger

Interior and heads lighting

Exterior lighting

Jabsco 24v toilet

Windscreen wipers (HD) supplied and fitted 2 centre screens

Supply and Install 4 x 24v Spot Lights


Engine Electrics

Supply 4 x heavy duty batteries, isolation switches & VCU's

wired back to engines and connect to dashboard looms for engine




Engine Water cooling

Inlet, Ball valves, Strainer, glass reinforcing ply into

hull for seacock and filter board connect all hoses back to engine


Exhaust system

2 x Exhaust hose, connected to (risers), rubber transom

Halyard inline silencers


Engine controls

Throttle and gear single unit dual morse control supplied



Hydraulic steering supplied and fitted

Supply and fit rudders


Plumbing and Heating

1 Elec bilge pump per engine bay - Manual operation only

auto / manual alarms to engine bay

1 Elec bilge pump for all other hull compartments - Manual/Auto operation

switches and auto / manual alarms to engine bay ref Seafish/MCA

Supply 4 x manual bilge pumps

Supply and fit with tap sink unit to toilet cubicle

Supply and fit galley sink and tap

Supply and fit pressurised water system including 40 gallon water tank and pump

Supply install waste water tank 25gal with 3 way diverter valve

Supply and fit Calorifier


Generators and AC Power

Supply and fit ring main with 3 outlets and shore power inlet

6kva/5.1kW Generator


Anchor winches and Hauling gear

Supply and fit hydraulic 1 tonne capstan with drum

Anchors (x2) chain and warp



Factory boat lift and lifting services

Oil up engines and antifreeze

Fuel for sea trials



3 names with port of registry

Safety Labels for COP

Std charge for Code of Practice inspection

Stability Book inc draft marks and load line


Engines and ancillary items

Engines Iveco C9 620 (550)

Twin Disc 5065A


Separ Filters

loom extensions


Double Front Pulley

Calorifier Fittings


Extras or client specified items

Install bridge electronics assumes 6 items

Searchlight RC 24v

Deckwash electric

House battery system

Safety equipment 12 persons to MCA code of practice

(excludes Life Rafts)

Opening hatch above helm

Fitting of liferaft brackets


Furuno Electronics Package



1 Furuno M1835 Colour 10.4” display, 24” radome c/w 15m cable



1 x Furuno FCV587 Colour 8.4” Dual frequency 50/200kHz echosounder

1 x Furuno 5PSD/AIR plastic through hull transducer



1 x Montana 600 handheld GPS marine bundle c/w g2 Blue chart UK & Ireland


Olex 3D Charting System

1 x Olex 3D Charting System comprising; 12/24vDC Boxer commercial grade PC with dual screen output, keyboard, trackball & USB pen, one Olex Chart (Area to be selected by customer)

17” Glass fronted monitor (12 volt DC)

PV3i 24-12 VDC, 3 amp isolated DC-DC converter

Actisense NMEA Opto-isolators for data



1 x Navitron NT777 comprising control unit, distribution box & rudder feedback unit.

Constant running pump 0 to 2.5 litres/min 24volt DC

Fluxgate sensor for autopilot heading.



1 x Furuno GP33 Colour GPS with 4.3” display and external antenna


Fixed VHF Radios

2 x Icom IC-M423 DSC / VHF Radio c/w fist mike

2 x Shakespeare RV240 2.4m VHF antenna c/w 6m cable

2 x VTronix ARMNT Stainless steel antenna base

 2 x PV6S 24-12 volt DC converter for VHF radio

1 x Koden GPS-20A GPS sensor for emergency GPS position to one DSC VHF


Handheld VHF Radio

2  Icom IC-M91D handheld VHF radio with DSC & GPS



1 x Kannad Automatic EPIRB in float free auto release container, Wheelmarked.

1 x Kannad Rescuer SART


Offered by Solent Brokers agents for Blyth Workcats: POA


Further Information Tel: +44 (0) 1983 282 777   or   Email:

Drop files to upload